|
|
Polypropylene and the CP64
(Preview)
about two weeks ago I tried a sample roll of Magic GFPOLYSIJ (intelicoat) on my CP64, ran great! ordered a batch and sold a job on it.. on the first print the poly stuck to the backheater and caused a head crash!!! (looked away for a second), cleared that and started up again, noticed the sticking,...
|
jmz
|
4
|
1265
|
|
|
|
|
|
Engine Error 1253
(Preview)
Hi everybody. I have three questions:
1.) Does anybody know what the Engine Error 1253 means?
2.) Could anybody has a error-code list and could send me?
3.) Has anybody a wiring diagram?
Thank you for every hint or answer!
Greets Steffen
|
roboplotter
|
4
|
1761
|
|
|
|
|
|
Backlit Media
(Preview)
Anyone have any good suggestions for a non-adhesive backlit film media for lightboxes and such? Thanks!
|
Wonsngis
|
4
|
1124
|
|
|
|
|
|
3M IJ40 series
(Preview)
Hi All
We have had our printer for about 4 months now and I find if I print on anything other than 180C and 8 pass 720dpi then i get pretty crappy results. I am trying to reprint a job that was origianally printed on the 180C but now is being done on IJ140 and the gradient on the image is coming through awful....
|
AussieGirl
|
4
|
2823
|
|
|
|
|
|
Material waste
(Preview)
Does anyone know why some of the time when you send a job to the printer it rolls out about a yard of material?
This only happens about 50% of the time. I have to cancel the job roll back the material resend yadda yadda. Seriously a pain.
Any way I can stop it from doing this?
|
seattle
|
4
|
737
|
|
|
|
|
|
Media
(Preview)
Anyone have any good media advice.
I am looking for tranaparent white vinyl. I use 3M scotchcal film right now and the quality is good but it costs 900 dollars a roll, and with this Seiko I have to reprint alot.
I have tried some cheaper stuff in the past but it was horrible, it would start turning into...
|
seattle
|
4
|
658
|
|
|
|
|
|
Streaks in solid red an blue prints???
(Preview)
I'm getting streaks in solid reds and blues, I don't think I'd call it banding. In a solid block of red, every 1.5" there is a streak of colour that is more yellow than the rest. The end result is a striped looking print, with these more yellow streaks every 1.5". The tech says the...
|
ahoce
|
3
|
1043
|
|
|
|
|
|
Leaving heads in "Fill Cap" condition
(Preview)
We have several different printers in-house (Dye-sub, solvent, UV flatbed, pigment inkjet), so my 64S may go several days without being used. Is the "Fill Cap" mode the best way for it to sit for a few days at a time?
|
RoCo
|
3
|
1055
|
|
|
|
|
|
FlexiSign and Adobe Illustrator and Colorpainter
(Preview)
Need some assistance. I'm using Flexi 7.6 with my 64S, when I import a file such as a EPS designed in Adobe Illustrator, there is a big color shift when opened in FlexiSign.
I know this is more a question regarding Flexi, but was hoping someone here has a possible solution.
I'll be contacting Sc...
|
Anonymous
|
3
|
981
|
|
Sep 11, 2005
by Anonymous
|
|
|
|
On site service other than Seiko techs?
(Preview)
Does anyone know of a third party that will come to your location and do maintenance to the printer?
|
JoeVinyl
|
3
|
976
|
|
|
|
|
|
Service Manual for Seiko 64S
(Preview)
Can I get the Service Manual of Seiko 64S. I specifically want to look at the Technical Diagram of the Machine. My email address is: signsngraphics@Hotmail.com Thanks Jim
|
Ravian80
|
3
|
3693
|
|
|
|
|
|
changing capping unit
(Preview)
my capping unit is not working properly
so I took a who;e capping unit off a old machine
Im afraid that while changing tubes I will damage the part
anyone has any advice
how to do it
|
dataprint
|
3
|
1039
|
|
|
|
|
|
Upgrade and downgrade the firmware
(Preview)
Dear Friends,
Can anyone tell me that if its possible to downgrade the firmware from version 2.10 to V2.0?
does printer supports downgrade function?
My 2nd question:
Are the firmware's of 64s and 100s same?
I expect replies from the experts who have tired this practi...
|
Mark
|
3
|
929
|
|
|
|
|
|
Autoupdate: now...blue, magenta, yellow outlines on white...?
(Preview)
I recently updated Onyx because our printing computers are not connected to the internet to prevent problems. After the update we ran a 52' trailer. I noticed after the fact that around all the areas with white and other light colors...there are thin blue, magenta, and yellow lines outlining them. I...
|
jpg_inc
|
3
|
770
|
|
|
|
|
|
Change cartridge error.
(Preview)
Hi there , my printer is rejecting magenta cartrige , I have put six new ones and it keeps requesting check cartrige and if I pull it out and re insert it says change cartridge . I have a changed a whole set already and it keeps requesting I change margenta . Can senior members help me out please ?
|
clockwork
|
3
|
877
|
|
|
|
|
|
i have an erro on my OCE 6060
(Preview)
this is the error ENGINE ERROR11E0 POWER OFF/ON Can anubody tell me what to do? i havent used for a couple of months and this is what it appears......does anybody knows the password of maintenance?
|
Bryan
|
3
|
1473
|
|
|
|
|
|
EROR 11C0
(Preview)
Sorry the eror i have is 11CO and not 12C0, If you have any idea please advise. thanks Ziv
|
zivkn
|
3
|
1168
|
|
|
|
|
|
Black Problems?
(Preview)
Anyone have problems with the black head, at this moment i can't reach a  real black , it's look like the head had some blocked nozzles.
Anyone with same problem ?
Phill
|
Phillgreat
|
3
|
897
|
|
|
|
|
|
carriage or trailing cables - Source?
(Preview)
I am looking for the a source for the trailing or carriage cables. They were $47 usd on the 2005 retail Seiko pricelist, now most dealers including HP and Oce want over $200 each, which is ridiculous. Does anyone know of a good source in the US?
|
monstercolor
|
3
|
1320
|
|
|
|
|
|
Engine error 11E0
(Preview)
Hi, I have this error, and I know how to clear it. The problem it's that I brought thi printer used, and he ask me about password. Anywone know how to clear it or the default password??
|
adrian0605
|
3
|
2728
|
|
|
